Replacing uPVC Window Handles

It is simple to change the handles on windows made of Upvc. The most important thing is to make sure that the replacement handle fits the spindle carved out in the window mechanism.

If you follow the steps below any cockspur handle can fit in most windows. The height of the step of the handle is crucial.

What to Do You Look For?

A lot of windows in the UK come with uPVC handles for doors and, over time, they will begin to show signs of wear and tear. When this occurs, the window handle can become loose or difficult to operate, making it essential to replace it. Anyone who is comfortable using a basic hand tool can complete this relatively simple task.

The first step is to ensure that the handle is securely attached to the frame of the window and in the open position. The next step is to locate the screws or pins which hold the handle in place. These are typically located on the inside of the handle and can be removed with a screwdriver or pliers.

Once the handle has become loose, gently pull it away from its hinges. The next step is to find a new handle that is the same design and size. This can be done at a DIY store or online. The procedure should take just five minutes, and you will need a screwdriver is all you need.

One crucial aspect to take into consideration when replacing a uPVC window handle is its step height. This is the distance from the bottom of the handle until it sits on the locking window handles frame. This is a common measurement and you should check the step height before ordering an replacement handle.

There are a variety of sizes based on the kind of handle. Inline handles for uPVC windows typically have 31mm lug centres as well as handles with cockspur that have 43mm centres. Tilt-and turn handles are typically found on uPVC windows. They feature a unique design which allows the window be slid down to let in air and then rotated to fully open the window.

The most common uPVC handle cracks are internal, instead of a break at the base. This makes it difficult to open. It is essential to make sure that any replacement handle has the same spindle as your original one.

Remove the old Handle

Incorrectly installed or damaged window handles could cause double-glazed windows to close or open in a way that isn't correct and may result in them getting stuck. This could be due to a number of factors, such as general wear and tear on the handle or corrosion. In these situations, it is vital to replace the upvc window handle as promptly as you can to avoid further damage or loss of function.

When replacing upvc windows handles it is recommended to remove the handles that were previously installed from the window. Begin by removing the screw by the handle while it is in the closed position. This should reveal another screw and once removed, you can begin to take off the handle itself. You can make the process easier by using an electric screwdriver.

Be adards for sizing, so it's relatively easy to identify the right size.

To measure the size of your handle, first remove it from the window by turning it to the open position. You should be able to see the dimensions of the screw or pin that holds the handle. Use a ruler or tape measure to determine how long the spindle is. Once you know the length of the spindle you can purchase a new one with exactly the same size.

The step height of a window handle is another factor to take into consideration when you are buying replacements. The step height is measured from the base to the point at which the handle sits on the frame. Typically, this is about 21mm for uPVC windows or 9mm for aluminium. To make sure that the new handle will fit it, you can drop something into the gap to determine how far it goes before meeting an obstruction.

Cockspur handles may have different backsets depending on what type of window you put them in. Inline espag handle heights are 43mm from centre to center (two fixing points). Cockspur handles however, have different backset heights according to the design of the window they are in. This is because they have a spur which extends from their handle and locks onto a cockspur wedge-striking plate.

Fit the New Handle

If you've decided to replace the handle, ensure that it is aligned to the screw holes in the patio door handle and secure it using the screws supplied. If you're replacing the latch lever the lever can be mounted in a similar way to the main door handle. Then, you can attach the door handle repair near me trim to conceal the mounting screws.

Tips: To remove the metal head from a wooden wedge place the handle on the floor, so that its wide end is on the ground. Then, you can use a hammer and tap the narrow end. Be careful not to scratch the handle or the spindle.