UPVC Replacement Door Handles

Over time the handles on your doors will wear out and require replacement. It is important to be able to match the dimensions of the old handles when replacing them.

The top screw position as well as the lever and keyhole size are the three measurements you need to determine. Use the size guide to help with this.

Inline Lever/Lever

A lever door handle is a contemporary handle that can be used on new or replacement doors. This kind door handle is offered in a variety of designs and finishes. A variety of manufacturers provide this handle, including Avocet ERA, Fullex, Hoppe, Mila, Millenco & Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The uPVC/Composite door handles are made of robust materials and are suitable for doors with multi-point locks which require a robust design. The handles are inline, and they use the same spindle and screws to secure them. They are easily fitted on any uPVC/Composite doors.

The design of the sprung lever allows the handle to be set and [Redirect Only] angled to provide a comfortable grip and is suitable for all users. The handle has been endurance-tested to 200 000 cycles. This helps to ensure that the finish is of high quality and performance is maintained over time. The sprung lever can also be shortened to fit a wider range of locks. This is useful in doors that are narrower, where the cylinder is further away from the door. A lever that is shorter is a good choice for doors where the latch can be activated by the thumb turn inside.

Lever Pad

The lever pad upvc handle is distinct from the lever handles that are commonly found on doors. These handles are operated by one spindle or two spindles inline or offset. They are typically employed on UPVC doors with double glazed door handle replacement glazing. They come in a variety of finishes & variations.

The handles are available in various finishes, including White chrome and Gold. The finish is compliant with BS EN 1670:2007 Grade 5 and is also resistant to corrosion, giving the handle a high level of durability and performance for its intended use.

All of the UPVC lever pad styles for handles come with screws and a spindle which allow them to be fitted on any new or existing uPVC patio door handle repair near me. The backplate fixing centres of 211mm allow for a wider handle, which can be beneficial in replacing a defective or worn multi point door lock mechanism. The handle levers are spring-loaded, thereby solving the issue of door handles sagging out of the horizontal position when not in use.

It is crucial to match the PZ dimensions of both the multipoint lock as well as the uPVC doors when selecting a replacement UPVC spindle and handle. This measurement is also known as the 'handle centre' or 'cylinder centres' and is a critical aspect in ensuring that you have the appropriate handlm the central fixing screw hole to the other end of the cylinder and the thumb turn if you have one. It is best to do this while the lock is in place however in the event that this is not feasible, you can take it off and remove it to measure. It is essential to ensure that there is no extension of the cylinder beyond the handle or escutcheon. This could make it susceptible to lock snapping attacks.

The design of many modern cylinders includes anti-drilling and bump resistance features. They are designed to decrease attack chances by forcing the cylinders to rotate in a different direction. This helps stop the attack and protect your doors.

Certain cylinders are made to resist snapping. This is a typical attack on cylinders. A specially designed tool is used to break the break line of the lock and then the front of cylinder is snapped off. This is much quicker and more straightforward than gaining access through a multipoint lock and leaves little evidence of a burglary, which can impede the insurance claim.

Spring Cassette

This spring cassette is found inside the base plate of your door handle. It is a spring-loaded solution to bring your multipoint lock handles back to their original position after using. The handles had no spring, and would slide when the locking mechanism was disconnected. Adding this simple component is one of the best ways to correct this issue and is an effective way to keep your doors made of upvc from becoming stuck in the open or closed position, as these are not always easy to manually close by hand.

These spring cassettes were created to be used with sprung multipoint locks. They will not fit handles that are not sprung and you'll have to cut a hole in your backplate for them to fit. (Please check the image for a detailed diagram). These cassettes are a solution to broken or missing cassettes in the backplate of uPVC door handles. They are supplied in a single unit. They come with a square cut out that accommodates an 8mm shaft.

These spring cassettes provide an excellent value solution for the problem of door handles that are sagging. These spring cassettes are simple to install and will extend the lifespan of your uPVC door. Contact us for more information on our selection of uPVC accessories and spares. We are available to assist and provide expert advice.