UPVC Replacement Door Handles

Over time, the handles on your doors will wear out and require replacement. It is crucial to match the dimensions of the handles you have previously replaced when replacing them.

The three measurements to check are the top screw's location, lever and key hole dimensions. Check the size guide for help with this.

Inline Lever/Lever

A lever/lever handle is a modern door handle designed to suit new or replacement doors. This type door handle is available in a wide range of styles and finishes. This handle is available from a number of manufacturers including Avocet ERA Fullex Hoppe Mila Millenco Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The uPVC/Composite door handles are made of robust materials and victorian Door Handle are suitable for doors with multi-point locks that require a strong design. The handles are inline and they utilize the same screws and spindle to secure them. They can be easily mounted on a new or existing uPVC/Composite doors.

The handle can be adjusted and angled to accommodate all users. The handle has been tested for endurance up to 200,000 cycles. This helps to ensure the quality of the finish as well as the performance of the handle over time. The sprung lever can be shortened to fit a wider range of locks. This is useful for doors with narrower openings where the cylinder is situated further back from the door. A lever that is shorter can be used on doors with latches that can be activated with the thumb located on the inside.

Lever Pad

A Lever Pad door handle made of upvc functions differently than lever handles on doors. These handle types can either use a single spindle (inline) or independently from each side using two offset spindles or inline (pad). They are typically employed on UPVC doors with double glazing and come in a variety of finishes & variations.

The handles have been tested to the minimum of 200,000 cycles and are available in a variety of finishes, including White Silver, Chrome, & Gold. The finish is BS EN 1670 Grade 5 and resistant to corrosion. This provides the handle with a high performance and durability for its intended purpose.

All UPVC lever pads for handles include a spindle and screws and can be mounted on a uPVC door. The backplate fixation centres of 211mm permit a larger handle, which is typically an advantage when replacing a damaged or old multi-point door lock mechanism. These handle levers are also sprung, solving the problem of handles hanging out of their horizontal position when they are not in use.

It is important to match up the PZ dimensions for both the multipoint lock as well as the replace upvc window handle doors when choosing a replacement UPVC spindle and handle. This measurement is also known as the "handle centre" or "cylinder centres which is a crucial aspect of matching up the appropriate handles.

After you have determined twith anti-drill and bump resistance features built into their design. These are designed to reduce the chances of an attack by causing the cylinder to rotate in an opposite direction. This can help deflect the attack, and protect your door.

There are cylinders that have been constructed to withstand snapping. This is an increasingly common type of attack on cylinders where the break line in the lock is targeted by a tool that is specially designed to break off the front of the cylinder and allow the door to open. This is a lot faster and less difficult than opening the door with a multipoint lock and leaves no evidence of a break-in which can impede an insurance claim.

Spring Cassette

This spring cassette is located within the base plate of the door handle. It is a spring-loaded solution to return the multipoint lock handles to their original position after use. The handles were previously equipped with no spring and would drop when the locking mechanism was disengaged. This component is the most effective way to fix this problem. It also prevents your upvc victorian door handle (learn more about imoodle.win) from becoming stuck in either the closed or open position as they aren't easy to close manually.

These spring cassettes are specially designed to be used with multipoint locks that are sprung They will not work with multipoint handles that are not sprung and you will require a bespoke hole cut into the backplate to allow them to fit (please see image for technical diagram). These cassettes can be used as a replacement to broken or missing cassettes that are in the backplate of replace upvc door handle door handles. They are sold as a single unit. They have a square-cut out that is able to accommodate an 8mm shaft.

These spring cassettes are a fantastic value-for-money solution to the issue of door handles that are that are sagging. They are simple to put in and will prolong the lifespan of your upvc window handle replacement doors. Contact us to learn more about our selection of uPVC accessories and spares. We are on hand to assist you and provide expert advice.