전화 및 상담예약 : 1588-7655

Free board 자유게시판

예약/상담 > 자유게시판

iPad 10th Gen LCD and Screen Replacement Guide How to Fix Your iPad 1…

페이지 정보

Barry 작성일24-08-20 22:28

본문


Welϲome Ьack tߋ аnother Gadget Kings video guide! Ιn thiѕ detailed tutorial, ѡe're going t᧐ ѕhoᴡ you how to replace both the screen аnd apple earphones lightning the LCD ߋn ɑn iPad 10tһ Gen, apple earphones lightning (https://gadgetkingsprs.com.au/phone-repair-drewvale) alѕo known ɑs the iPad 10.9". If your screen is cracked or the display isn't working correctly, this guide will help you fix it step by step. Let's dive in!

Getting Started

To begin, you will need a few essential tools: a heat gun or hair dryer, a heat mat, isopropyl alcohol, a single-sided razor blade, plastic guitar picks, a small scraping tool, a plastic spudger, and a UV curing lamp. These tools will make the process much smoother and ensure you don't damage any internal components.

Start by placing the iPad face down on the heat mat set to about 75°C for approximately 10 minutes. The purpose of this is to soften the adhesive holding the digitizer (the glass part of the screen) in place. Once the iPad has warmed up, flip it back over.

If your iPad has any additional attachments, such as a ring holder, it's best to leave it in place to avoid customer dissatisfaction. Begin by applying isopropyl alcohol to the edge of the iPad, soaking it into the gap between the screen and the digitizer. This will help loosen the adhesive further.

Removing the Digitizer

Use a single-sided razor blade to create a small gap between the chassis and the digitizer. Insert a plastic guitar pick into this gap and carefully run it along the edge of the screen. Insert the pick only a few millimeters at a time to avoid damaging the LCD beneath the glass. Lift the digitizer gently with your fingers while cutting through the adhesive.

Once the adhesive is cut through, you can lift the digitizer away from the chassis. The digitizer opens up like a book, with the cables located on one side. Be cautious not to touch the right-hand edge as it isn't necessary for opening the iPad.

Disassembling the iPad

With the digitizer removed, place the iPad back on the bench for further disassembly. If your iPad has any ring holders, you can use a piece of tape to secure them flat for easier handling. Begin by removing the eight T2 screws that hold down the LCD, four on each side. Carefully avoid touching the LCD to prevent any smudges or marks, which can be difficult to remove.

Lift the LCD away from the chassis by prying upwards with a spudger. The LCD should open up towards the bottom, similar to a notepad. Disconnect the power by removing the battery screw and placing a piece of plastic between the battery and the motherboard to isolatr/>
Finally, place the LCD into its final position, ensuring it sits correctly. Secure the corners with screws and apply pressure along the edges to ensure the adhesive sticks.

Testing and Final Steps

Turn on the device to test the functionality of the new screen and digitizer. Once confirmed, remove any protective films from the digitizer and LCD. Ensure there is no dust or debris inside before closing the iPad.

Apply gentle pressure around all four edges to secure the digitizer in place. Test all functionalities again before handing the iPad back to the customer.

Congratulations! You've successfully replaced the screen and LCD on your iPad 10th Gen.

For more detailed guides and professional repair services, visit Gadget Kings. Our expert technicians are always ready to assist you with any gadget repair needs. See you next time for another helpful tutorial!

댓글목록

등록된 댓글이 없습니다.


Warning: Unknown: write failed: Disk quota exceeded (122) in Unknown on line 0

Warning: Unknown: Failed to write session data (files). Please verify that the current setting of session.save_path is correct (/home2/hosting_users/cseeing/www/data/session) in Unknown on line 0